Technical & Reference Section > Tech and Restoration

flatting axles

<< < (2/4) > >>

ED209:
get stuck in with the angle grinder Gaz... lovely sparks

you just have to take it down gently and make sure you spin the axles 180 and keep checking you are doing it paralell  :)

BENDYCAT ELEVENTEEN:
Can't find my thread in sale section - so i guess it might have been deleted to make room  ???


the easy way is to buy one of my 8mm/10mm axles



 copied from burnerworld thread - have a look below






Right i have been resto'ing some of my hubs with a rebuild kit that i have - i have got a load of hubs/axles in and i take them apart and clean them up, they can be used to rebuild most standard hubs.

I have rebuilt up sets of Alloy hubbed Skyway mags with the cup bearings holders (not sealed bearing hubs) - you can replace most cup race bearing holder type mags and spoked wheels - although some might not fit so you will have to check first.

you can replace the axle to a standard fit size nut that is on a 10mm axle.

so i can do you a 10mm axle - a caged bearing race -  cone nuts that go against the bearings - the washer nut that sits tight next the cone nut - a bobble washer - a outside nut.

here is what the kit looks like








So you get

2x axle in black - 138mm long 10mm wide - standard thread size (not skyway size, so won't fit skyway nuts on)
4x caged bearing race in silver- 24mm across - 6mm deep - strong and well made.
4x cone nuts in black with removable skirt/shield, just tap it off or move up and down for a better fit - 17mm across 14mm deep on cone nut - 24mm across 2mm deep on shield.
4x washer nut in silver - 16mm across - 3mm deep
4x bobble washer in silver (well what would you call it ?) 16mm across - 2mm deep
4x outer nut in silver - 15mm across - 14mm deep



If you want a kit it will do both wheels - but please check rear drop out size of axle, as some can be wide (you can use your own rear axle with this kit if you need to fit wider )

i can sell a single half kit for one wheel if needed

kits will not be broken up for sale of individual parts


price's are

£10 posted for a kit (this is for two wheels)

£5 posted for a half kit (for one wheel )

if i get loads of members wanting this item, it may take a little while to sort the first load out - i have work and other members mags to restore + need to sleep and eat at some point !

please post in here and then a pm - if i don't get both you will miss out

they may not fit all, that is why i have given sizes -  so please realize I'm not perfect, just trying to help




GT STYLE 8mm cut side axle rebuild kit ~ Limited numbers !

£8 single kit posted

129mm in length - 10mm axle with the GT fork 8mm cut sides - this allows the axle to slip in to the 8mm axle gap on GT forks and such like.

bearing cage  25mm across 6mm deep cone nuts 15mm across 11mm deep -  cone nut washer 15mm across 3 mm deep - washer with groves on one side 19mm across 2mm deep - out side nut 15mm across 10mm deep - can also surply loose bearings on these.






cheers B  ;)


cheers B  ;)

rollin72:
thanks for that Bendy, my head hurts ;D

they are new tuffs with sealed bearings so that wont work :-\

BENDYCAT ELEVENTEEN:
worked on mine - if it's just one - i might have a spare one without the rest of the parts

there is about 1mm diff in width but when don up you won't notice any thing

pm if you want the easy way  ;)

Retrodan72:

--- Quote from: rollin72 on February 10, 2012, 07:41 PM ---thanks for that Bendy, my head hurts ;D

they are new tuffs with sealed bearings so that wont work :-\

--- End quote ---

I just used a Dremel with a small abrasive wheel on the end. :daumenhoch:

Navigation

[0] Message Index

[#] Next page

[*] Previous page