1
Tech and Restoration / Re: Another project. This time it's a lambo !
« Last post by Midschoolfool on May 31, 2024, 01:15 PM »Lambo build now has Lambo doors. 
Wait for it....
Ayyyyyyyy
Wait for it....
Ayyyyyyyy
Recent Posts
2
Tech and Restoration / Re: Another project. This time it's a lambo !
« Last post by Midschoolfool on May 30, 2024, 08:08 PM »Yeah, dude it was FILTHY. It has been nearly three years since I have even so much as touched it.
The carbon post on it was never a good idea, due to the pinch design. It crunched that post. Thankfully not anywhere near where it matters for this build so I will cut it down.
OK so update time.
I ordered those a couple of days back. Grips should match the seat lovely. The frame came in today and is going to be a minor ball ache. First off the BB is Italian, but I think I still have the ends I removed in the reverse of this shit a couple of months back but secondly it needs a very obscure headset.
Semi integrated BUT 41.4mm, not the standard 44. That's the bloody Italians for you I am hoping that will sort that issue. I will then need to find these (the ends)
And fit them to my Octalink BB. Not hard.
Turned out the frame and fork were the same seller. Which was nice, as they gave me back a tenner. Those came in today.
The fork is a work of pure art.
Stunning. So I found some old style decal art (the type I want) online. Guy wanted 60 quid for them ass hat. I upscaled these using AI
Just for the lettering and "Treviso" part. Apparently the Pinarello Treviso has always been their top end model. Treviso is the town in Italy where they are based.
I ordered that a few days back from Ali Express. Came today. I love that. Proper takes me back to my childhood that does. I also have received the tyres, brake levers, brake cables and a few other smalls. The paint also came in today. I also had a pretty crazy idea. See, all of Pinarellos new frames are carbon. The one I got? 2012-2016. I love the look of forged carbon. It is stunning, so I got this.
I am going to cut the Pinarello lettering from that. The idea is that basically with those decals on it will look like the frame is carbon. At which point someone put gold candy over it, put the lettering on as stencils, painted it yellow and then took them off, exposing the carbon underneath.
The carbon post on it was never a good idea, due to the pinch design. It crunched that post. Thankfully not anywhere near where it matters for this build so I will cut it down.
OK so update time.
I ordered those a couple of days back. Grips should match the seat lovely. The frame came in today and is going to be a minor ball ache. First off the BB is Italian, but I think I still have the ends I removed in the reverse of this shit a couple of months back
but secondly it needs a very obscure headset.Semi integrated BUT 41.4mm, not the standard 44. That's the bloody Italians for you
I am hoping that will sort that issue. I will then need to find these (the ends)And fit them to my Octalink BB. Not hard.
Turned out the frame and fork were the same seller. Which was nice, as they gave me back a tenner. Those came in today.
The fork is a work of pure art.
Stunning. So I found some old style decal art (the type I want) online. Guy wanted 60 quid for them
ass hat. I upscaled these using AIJust for the lettering and "Treviso" part. Apparently the Pinarello Treviso has always been their top end model. Treviso is the town in Italy where they are based.
I ordered that a few days back from Ali Express. Came today. I love that. Proper takes me back to my childhood that does. I also have received the tyres, brake levers, brake cables and a few other smalls. The paint also came in today. I also had a pretty crazy idea. See, all of Pinarellos new frames are carbon. The one I got? 2012-2016. I love the look of forged carbon. It is stunning, so I got this.
I am going to cut the Pinarello lettering from that. The idea is that basically with those decals on it will look like the frame is carbon. At which point someone put gold candy over it, put the lettering on as stencils, painted it yellow and then took them off, exposing the carbon underneath.
3
Events / Re: 2024 rides I know of
« Last post by brettypeeps on May 29, 2024, 06:01 PM »Loads more added 
4
Tech and Restoration / Re: Another project. This time it's a lambo !
« Last post by Mikku on May 29, 2024, 11:56 AM »Intrigued to see how this goes. 
Nice to see that GT again too!
Nice to see that GT again too!
5
New School Racing / Re: 2024 Race Blog - Year 8 - It's Never Too Late!!
« Last post by Mikku on May 29, 2024, 11:51 AM »Both race meetings went ahead as scheduled last Sunday, so I chose to go down to Osaka, the rationale being a better chance of more riders and therefore race action. Surprisingly, Joetsu actually had 7 riders enter the over 30s class, meaning that I would have made it a full gate had I gone up there. No regrets though, because I had a good day at Oizumi. There were 12 riders in their over 30s class, so we were split into two racks of 6, with the top four from each going through to the main. I had some close racing in every moto, managing to take 4th, 4th and 4th in each one to qualify for the main. Making the main event at Oizumi is quite often out of my reach, so I was happy with that and couldn't really complain about the subsequent 8th place finish. Overall though, I rode quite well and felt strong throughout the day. There's plenty more to work on, of course, but the important thing for me was making the main with some good dices en route. Below is a video of the third moto, with me in lane 5.
/>
The next scheduled race is at Joetsu on 23rd June, with Oizumi the following weekend. The Japanese rainy season may have something to say about that, but hopefully at least one of those meetings goes ahead, if not both.
/>
The next scheduled race is at Joetsu on 23rd June, with Oizumi the following weekend. The Japanese rainy season may have something to say about that, but hopefully at least one of those meetings goes ahead, if not both.
6
BMX Chat / Re: Me Tarzan, you Jane.
« Last post by Midschoolfool on May 28, 2024, 02:16 PM »OK to catch up. The bike is mostly built now, sans the sprocket and rear pegs.
I made the upper cable out of a lower. I wish I hadn't, it was such a dick. It works though. If you were wondering why I did this? because it was free. I really don't want to sink another penny into this.
The peg washers came today. I didn't want to fit the rear pegs (they are 10mm btw to match the axles) without some support. The adapters in there now are about 3mm high, then the pegs start. So if you stood on them? they would tip and bend the axle. They need these which just arrived.
But there is little point given I am waiting on the sprocket to be machined. The Pro Taper grips came and they are the perfect length, so I will probably fit those tomorrow.
I made the upper cable out of a lower. I wish I hadn't, it was such a dick. It works though. If you were wondering why I did this? because it was free. I really don't want to sink another penny into this.
The peg washers came today. I didn't want to fit the rear pegs (they are 10mm btw to match the axles) without some support. The adapters in there now are about 3mm high, then the pegs start. So if you stood on them? they would tip and bend the axle. They need these which just arrived.
But there is little point given I am waiting on the sprocket to be machined. The Pro Taper grips came and they are the perfect length, so I will probably fit those tomorrow.
7
Tech and Restoration / Another project. This time it's a lambo !
« Last post by Midschoolfool on May 27, 2024, 03:34 PM »So I now refer to the Ti bike as "My Ferrari". I only gave it that nickname when I noticed how much red I had put on it. Thing is it shares a lot in common with a rari. Mostly I never take it out in the wet, polish and clean it on the regs and it's the sports car of bikes.
So, even though that one ended up quite spendy (1500 quid. That is A LOT of bike for that much, the frame RRP is 400 quid more ffs !) this one should not. I reckon about a third, to half of that. That doesn't mean it will be crap, I just got really lucky....
So the other day I was looking on the bay after a mate on another forum asked where I kept getting all the frames from. I went and looked for him but you know how it ends up
Well what I found was some NOS unpainted frames. Bianchi, Pinarello etc. Like, literally cutting edge frames of the time. This particular one is a Pinarello Treviso and back in 2014 it cost about 5 grand.
Because these bikes were so expensive they used to send them out like that. IE, at that price the customer could then specify a colour and they would paint it. The only image I can find of a complete one is this.
It's gorgeous. How much for the frames? 45 quid
I shit thee not.So my mate grabbed one, and then I might have grabbed one too. My brother came over to collect my old PK, like this.
And we got chatting and yeah he may have ended up taking my frame the bastud. I then ordered another.
The nice thing is she is literally ready. What prep work is required is absolutely minimal. They have even smoothed off the head tube, primed it and etc. So that got the ideas flowing. I have a bike with lots of red, let's do a lambo inspired build.
"Pineapple Passion" it is called. Proper 2k bobby and all.
I then started calculating what parts I needed. Turns out I already had a load. I did not, however, have a fork so I got this from the same place for 80 quid.
Ridley carbon fork. This bike is going to have rear gears. The first I have ever done.
I then ordered a lot of parts. First stop was Ali Express looking for some bars and I found them too.
25.4 clamping area. So I got a stem on there too for a fiver (the bars were 35 inc shipping and VAT).
So that is the front end and steering sorted. I then proceeded to gentlemans relish 150 quid on brakes.
And.
When I took the Ti bike out for the test run and speed test (fook me it's fast) I ripped the back of my leg open bringing it back up the stairs. Which made me very angry, as I got blood all over my shorts. So I found these.
You insert two fingers, pull the lever out and they fold up. Cables.
Wheels I am not sure about yet. Like I say, I have never ever set up gears before so the wheels will be ordered last minute. What I did know was this was sitting in the loft.
And the cranks on it are not safe for a BMX. They are hollow carbon, and they flex inward. So you can not stand up and ride on them. As such I had no problem doing this.
'cause I am having that seat post too. I am 99% sure the seat tube on the Pinarello is 27.2
Then a set of fatter tyres. 28c.
With enough grip to go over gravel and stones (something I would not be happy about doing on the Ti bike !).
I only really need wheels now, but again I will wait until I am ready. Oh and a rear derailleur and a simple bar mount shifter. For the seat I will finally be using this.
Frame should arrive fast (last one did) and the paint should arrive by Weds too. I am hoping to get it all painted by the end of the week.
8
Tech and Restoration / Re: A dream of mine. Not a BMX, but has some BMX parts
« Last post by Midschoolfool on May 25, 2024, 05:25 PM »I was right. It fookin FLIES
Was taking a rest.
Perfect spot for it. So tranquil.
Was taking a rest.
Perfect spot for it. So tranquil.
9
BMX Chat / Re: Me Tarzan, you Jane.
« Last post by Midschoolfool on May 23, 2024, 06:21 PM »My pegs and seat clamp arrived just as I was about to walk out of the door. So I got a quick pic.
I had to come back to finish the PK for my brother. He is coming Saturday to collect me and the bike. So I got that done yesterday and am now enjoying some down time. What I love most about those pegs is the size. They are far smaller than they seem. It will be more apparent once they are on the frame etc but yeah, look at them compared to the seat clamp. More pegs should be that size tbh.
I have ordered these too.
I have a pile of axle adapters but not ones for pegs. What I mean is they are only about 16mm at the flared part. This means that when you put pegs on there is a 2mm gap between the peg and the drop. IE, if I stand my fat ass on said pegs they will bend the axles in moments. Those are sized to take the whole peg end.
I also ordered these. Might use them, might not. The T1 grips are a bit long and encroach on the brake levers.
Sprocket was sent to my mate to machine out today.
I had to come back to finish the PK for my brother. He is coming Saturday to collect me and the bike. So I got that done yesterday and am now enjoying some down time. What I love most about those pegs is the size. They are far smaller than they seem. It will be more apparent once they are on the frame etc but yeah, look at them compared to the seat clamp. More pegs should be that size tbh.
I have ordered these too.
I have a pile of axle adapters but not ones for pegs. What I mean is they are only about 16mm at the flared part. This means that when you put pegs on there is a 2mm gap between the peg and the drop. IE, if I stand my fat ass on said pegs they will bend the axles in moments. Those are sized to take the whole peg end.
I also ordered these. Might use them, might not. The T1 grips are a bit long and encroach on the brake levers.
Sprocket was sent to my mate to machine out today.
10
BMX Chat / Re: Me Tarzan, you Jane.
« Last post by Midschoolfool on May 21, 2024, 04:00 PM »See you all next week. 
