RADBMX.CO.UK

Technical & Reference Section => Tech and Restoration => Topic started by: 20to26 on June 18, 2010, 11:15 AM

Title: decals won't stay stuck...
Post by: 20to26 on June 18, 2010, 11:15 AM
ok this is annoying - I've been applying decals to my fresh SBD powdered Kuwahara frames and the decals will not stay stuck down - the edges are lifting.

I've read the posts on here and used paint prep wipes to clean the frame in the area where the decals would be placed - but the decals are still lifting!

any ideas?
Title: Re: decals won't stay stuck...
Post by: firebird on June 18, 2010, 11:18 AM
once the frame is clean, how are you fitting the decals?
Title: Re: decals won't stay stuck...
Post by: 20to26 on June 18, 2010, 11:20 AM
just applying them directly - positioning isn't a problem with the Kuwahara decals as they're all quite small or narrow.
Title: Re: decals won't stay stuck...
Post by: firebird on June 18, 2010, 11:22 AM
ok, so no water or anything like that?
Title: Re: decals won't stay stuck...
Post by: Del on June 18, 2010, 11:22 AM
are they those thick glossy ones?
Title: Re: decals won't stay stuck...
Post by: 20to26 on June 18, 2010, 11:24 AM
nope no soapy water Firebird

and yeah they're quite thick & glossy Del
Title: Re: decals won't stay stuck...
Post by: stevochb on June 18, 2010, 11:31 AM
Ive got the same problem with my kuw decals, they went on fine but after a couple of days started lifting at the edges :(
Title: Re: decals won't stay stuck...
Post by: Glynnyboy on June 18, 2010, 01:13 PM
I had some original one's that did the same thing. The problem with them was age, the stickie had gone funny in the sunlight over the years. Sometimes it's nice to have original but only if they actually stick on the f/f ::)
Title: Re: decals won't stay stuck...
Post by: MartyC on June 18, 2010, 01:37 PM
Try a hair dryer to warm them up and failing that try some instant contact adhesive  :-\.
Title: Re: decals won't stay stuck...
Post by: 20to26 on June 18, 2010, 01:41 PM
funnily the one on that I know for sure is 80's has stuck without any problems on the headtube - the others are not sticking. I've stuck the edges down now with masking tape.

I'm going to try the hairdryer Marty cheers mate!

Perhaps the combination of warming them up and holding the edges down with masking tape might form them to the tubing.
Title: Re: decals won't stay stuck...
Post by: brass monkey! on June 18, 2010, 02:01 PM
had a similar issue with foil backed Torker fork decals, in the end i put a dab of Pritt Stick on em, and it has sorted the problem... :)
Title: Re: decals won't stay stuck...
Post by: southern andy on June 18, 2010, 03:19 PM
I'm sure you can get an adhesive spray. 3M or scotchguard do something like it.

We used to use it for vinyl's at work when they weren't very sticky.


Maybe one of these may work, just spray the back of the sticker and fit too frame.


http://shop.ebay.co.uk/?_from=R40&_trksid=p3984.m570.l1313&_nkw=adhesive+spray&_sacat=See-All-Categories
Title: Re: decals won't stay stuck...
Post by: 20to26 on June 18, 2010, 03:30 PM
good idea! that's next if my hairdried-maksing-taped decal trick doesn't work... thanks Andy
Title: Re: decals won't stay stuck...
Post by: DJL on July 13, 2010, 08:47 AM
did the hairdryer work?  if not did you find a way of getting them to stick?  i'm having the same problem......
Title: Re: decals won't stay stuck...
Post by: mark 2 on July 13, 2010, 09:24 AM
Ive got the same problem with my kuw decals, they went on fine but after a couple of days started lifting at the edges :(



I'm in the club
SimplePortal 2.3.5 © 2008-2012, SimplePortal