RADBMX.CO.UK
Technical & Reference Section => Tech and Restoration => Topic started by: crazycraig on August 29, 2011, 10:23 PM
-
:wtf: :wtf: :wtf: am i going going to do ?
I have a suntour XC spindal stuck in and cant get it out for nothing . I have soaked it in WD , I have had it in the vice with no joy .
Any ideas ? ? ? ?
:-[
-
you tried heating and rapid cooling it?
-
Soak it in diesel... :daumenhoch:
-
No i have not wildon . Do you suggest heating the spindal or the crank arm ?
-
Soak it in diesel... :daumenhoch:
I have soaked it in WD would that not be better than diesel ?
-
Turn it the other way ? might sound strange but you might be tightening it ? just a thought ???
-
No i have not wildon . Do you suggest heating the spindal or the crank arm ?
i'd heat the spindle as it might cause some damage to the chrome on the arm. seen someone do it on youtube where he heated it with a blow torch then dipped it in ice water and repeated that a few times :daumenhoch:
-
That was diggler's advice to a similar problem.... sprocket bolt seized
Must admit i've not tried it... sprocket's still stuck to the crank arm... ;D
-
I've had this before:
Buy a long pedal spanner, put the spanner and the crank down so that they make a upside down V (^) raised from the floor you might need to get someone to hold them or prop them with their foot.
press down with your foot on the top of the 'V'
Remember that pedals always tighten in a forward motion, so that when you pedal the pedal is kept tight.
That means that the non-drive side will untighten clockwise if you are looking at it side on.
-
Think i may try the heat route ..........
Whats the worst case scenario here .......... I end up with an Andy Patterson JMC with suntour XC's on or even worse lose a crank set :'(
-
Thanks for the advice chaps .......... I am hoping someone else will offer to do it ........So i can blame someone else :D
-
i'll do it for you :D
-
try coke~a~cola - it will eat the rust and not just slip past it - half an hour in and then try the long crank spaner on the floor and put weight on it ;)
-
You are undoing it by turning it clockwise Craig?
Vice on the spindle, rubber hammer on the arm otherwise.
-
:daumenhoch:
-
You are undoing it by turning it clockwise Craig?
Vice on the spindle, rubber hammer on the arm otherwise.
Good idear
Vice in spindle scaffolding bar over crank = leverage
If the spindle slips round weld a bolt or bar across it.
-
Try boiling water for heat.
-
SMASHHHHHHHHHHHHHHHHH ITTTTTTTTTTTTTTTTTTTTTTTTTTT :knuppel2:
-
(http://1.bp.blogspot.com/-kFzX1n6tk-s/Tgt3d6l02wI/AAAAAAAAAFA/f5liYeQWavc/s1600/salt.jpg)
-
salt mends everything :crazy2:
-
If You heat the spindle then the spindle will expand
It's the crank you need to expand so the spindle comes out
-
Rule number 1 ; Always grease your threads before fitting :D
-
Ring a local Engineering company they may be able to freeze it out for you (costs but works better than heat) or get it drilled out by somebody who knows what they are doing
-
I will have a do when i get home at the weekend and report back !!!! Thanks again fellas :daumenhoch:
-
If you struggle, drop it off at mine and I'll sort it at work.
-
Wow !!!! Nice one JT :-*
-
Ffs Craig and tools, just stick to body dying
-
:LolLolLolLol:
I wondered when you would stumble accross the thread
-
Ring a local Engineering company they may be able to freeze it out for you (costs but works better than heat) or get it drilled out by somebody who knows what they are doing
you could try some "ROSTOFF ICE" made by Wurth.It's a freezing spray.
-
go with bendy and try coca cola that stuff is lethal or try release fluid
-
I need a drive side only so if it goes wrong I'll have the drive side please lol
-
you could try some "ROSTOFF ICE"
Isn't that where Scooby Doo posts his letters?
-
Fookinell. ;D ;D ;D ;D
-
Done it !!! brute force and vice :)
-
Well done :daumenhoch:
-
shit :-[ was going to say sell em to me cheap and i'll get it out no problem :daumenhoch:
-
I put them in the for sale area up for offers and no one sniffed >:(
-
I put them in the for sale area up for offers and no one sniffed >:(
i did but you had changed your mind by then :LolLolLolLol:
-
I didnt want to give it up :-\