RADBMX.CO.UK

Technical & Reference Section => Tech and Restoration => Topic started by: crazycraig on September 06, 2011, 04:43 PM

Title: How do you replicate the brush finish on a tuf neck stem ?
Post by: crazycraig on September 06, 2011, 04:43 PM
As the title says .

I have a pro model tuf neck that i want to re anno . trouble is its had the living daylights polished out of it ! I want replicate the original finish before i get it re anno'd


So whats the best way ? Any process pictures would be good  :daumenhoch:
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: GTnumber1 on September 06, 2011, 04:51 PM
it needs to have bolloxed polished out of it to get anno`d  8)
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: crazycraig on September 06, 2011, 04:52 PM
 ::)

I dont think it does but could be wrong 
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: bobafett on September 06, 2011, 05:01 PM

If you are going to Paul at CCA for the anodising Craig I think he will actually do the brushed finished for you first mate  :daumenhoch:

Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: crazycraig on September 06, 2011, 05:02 PM
Even better !!!!

It would be good to see a step by step process on here though  :-\
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: bobafett on September 06, 2011, 05:11 PM

SteveP was the master at doing the brushed look - have a search through his posts or look at his interview in the interview section  :laugh:

Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: rollin72 on September 06, 2011, 05:15 PM
snav did it with sandpaper..looks alright
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: meticulous on September 06, 2011, 05:29 PM
tape it to your arse on thursday, and when you fall off doing your track day you will automatically recreate the scrape finish....       :D

better still!  tape it to your bar ends....        ;D
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: dordymush on September 06, 2011, 05:38 PM
steve done his with a wet stone.
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: crazycraig on September 06, 2011, 06:12 PM
tape it to your arse on thursday, and when you fall off doing your track day you will automatically recreate the scrape finish....       :D

better still!  tape it to your bar ends....        ;D
I will be selling tuf neck seat clamps on Friday ........In Green !
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: CD17 on September 06, 2011, 06:42 PM
Craig, have a look here  :daumenhoch:

http://www.radbmx.co.uk/forum/index.php'topic=131924.msg1271234#msg1271234
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: crazycraig on September 06, 2011, 06:43 PM
 :daumenhoch:
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: meticulous on September 06, 2011, 07:10 PM
 :daumenhoch:
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: MartyC on September 07, 2011, 12:35 PM
Linisher  :P
Title: Re: How do you replicate the brush finish on a tuf neck stem ?
Post by: jT Racing on September 07, 2011, 01:03 PM
Get some scotch pads craig, the grey ones, red will be too fine and make sure you go in straight lines. Piece of urine.
SimplePortal 2.3.5 © 2008-2012, SimplePortal