RADBMX.CO.UK
Technical & Reference Section => Tech and Restoration => Topic started by: animal on November 15, 2011, 06:13 PM
-
just wondering cos just got 1 with the stamp etc on but its been sanded so not at indented as needs 2 b ::) is it the way 2 go ?
-
i asked about that ages ago steve
i'll check through my pm's in a min for ya as theres a fella on here that was gonna have a go at mine for me as thats sanded down.
i've only just managed to get a good enough picture for him to have a go at it for me.
hope he still on here lol.
-
I've got the same problem with mine, i took it to a local engravers and they said it could be done if i knew what font it was. I think i've found the font but i haven't been back since. I will get round to it eventually but there's no rush and i can't be bothered. ???
-
Carl In2Bmx did my dk stem, give him a shout he may be able to help you, just feed him plenty of beer and class A ;D
-
What type of Tuf Neck stem ?
-
I could do it if I re drew the logo . The text would be easier than the tiger but it could be done. :daumenhoch:
Here was a few we tested with :daumenhoch:
(http://www.radbmx.co.uk/archive/albums/ss250/in2signs/morerouting001.jpg)
-
I will sort u some piccys ;)
this is what I need ;)
(http://www.radbmx.co.uk/archive/albums/q103/animalmrd/IMG_2432.jpg)
2 b honest I would staighten this cap and reanno it , but not convinced it would b any good with the stress lines in it ::)
-
I need this one Carl.
(http://www.radbmx.co.uk/archive/albums/p191/carpcrazyox/SAM_0546.jpg)
should be this one but you know that already.
(http://www.radbmx.co.uk/archive/albums/p191/carpcrazyox/SAM_0547.jpg)
-
thats the one i need to.
-
sorry to go off topic slightly,but i was wondering after being sniped to a set of tuf neck chainring bolts on the bay,if it would be possible to engrave my plain ones with the'TUF NECK USA' logo? :-\
-
The tiger might take some doing . But the text one should be easy enough . :daumenhoch: the small DK logo you can see Is on a 10mm square . ^"^
Mad busy at the moment at work but I'll get one of my lads to re draw them .
I'll do some testing . :daumenhoch:
-
Here you go ..
(http://www.radbmx.co.uk/archive/albums/ss250/in2signs/stem005.jpg)
(http://www.radbmx.co.uk/archive/albums/ss250/in2signs/stem009.jpg)
-
::) I was just looking for a photo of that :daumenhoch:
-
Spot on , will get a pic of my stem top up 4 ya ;) Like I said its all there just a bit faint ::)
-
I've got a few tiger stamps I can copy Steve . :daumenhoch: I'll have a go . ;)
If anyone has a good example of the the one Dordy and Andy have I could do with a photo ( with the font height's) or a rubbing I can take some sizes off . ::) please .
-
Great work mate :4_17_5: handy having a man in the know ;)
-
If anyone has a good example of the the one Dordy and Andy have I could do with a photo ( with the font height's) or a rubbing I can take some sizes off . ::) please .
The one in my photo Carl was MarkyP's cap, i had it here a while to try and get it copied. The engraver i was going to use happened to go to OZ for a month at about the same time Mark needed his cap back.
I tried to do a rubbing with various things but the engraving on his was just too light to show up as Marks had been polished a bit too much aswell.
I'm sure i can measure the letters that are there on mine but someone may need to measure the patent pending bit.
-
I'll get Mark to take a straight on photo of his and tell me the letter sizes :daumenhoch:
That's all I should need .
-
The only reason i didn't take a straight on photo was my ugly mug was reflecting in it as it looked like a mirror, at least with Mary you're getting a pretty boy in the reflection :LolLolLolLol: