gfxgfx
 
logo
 
gfx gfx
gfx
975501 Posts in 138922 Topics by 6344 Members - Latest Member: MTBMX March 29, 2024, 01:08 PM
*
gfx* Home | Portal | Forum | Merchandise | Help | Login | Register | gfx
gfx
RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  Home made Pro Class wheels
gfx
gfxgfx
 

Author Topic: Home made Pro Class wheels  (Read 3992 times)

0 Members and 1 Guest are viewing this topic.

Offline benno

  • Team Moderator
  • 900 Air
  • *
  • Posts: 3888
  • Rated:
Home made Pro Class wheels
« on: November 10, 2018, 09:45 PM »
This is how I did it 👍🏼
This project started with some really ropey Araya 7x that I had kindly donated to me by a fellow stroud based Radster Jason ( burnerboy ) on here.
They were a bit beaten up but not beyond saving.
1 was gold and the other was silver so I got the caustic soda out and gave em a bit of a bath to remove the Anno.
With the Anno gone it was a case of out with the sander and working down the grades finishing up with wet sanding with 1000-2000 wet and dry.
I thought it was best to get the rims as good as possible before attacking them with the drill 😂
So I also gave em a good going over with autosol and then peek using my trusty polisher which is basically my orbital sander with circular microfibre cloth attached to it.
When they were at a reasonable standard it was time to start thinking about drilling alll the holes.
The problem was that all the spoke holes and the actual bobbles for the spoke holes are not all the same distance apart so trying to make a template was difficult.
After a few attempts on a practice set of scrap wheels I came up with a plan.
I stuck 1” masking tape across the rim between the bobbles ( in some of the pics you can telll the difference in the distance between em )
I then made a small plastic template with a small hole which was in the centre of the rim and roughly centre between the bobbles.
I then marked every hole with a biro and used a centre punch to give the drill a head start,
It was then a case of drilling every hole in stages starting with a 2mm bit then up to 4mm, 6mm, 8mm, 10mm and finishing with an 11mm hole using a stepper drill bit and being extra careful to stop before they got to 12mm 😂😂
This was actually quite good as it gave me a very slight counter sink and no burring
So that’s 420 holes in total 😱 but when I took the tape off it was deffo worth it.
I had previously bought some really nice Suzue hubs so I sent both the rims and hubs off to Rads resident wheel builder Danny Robbo and he did an excellent job as usuall
For the rim tape I bought some 15mm shiny blue ribbon from eBay and also some new standard rim tape the icing on the cake was the pro class valve hole decals from the main man Del and they were finished.
I’m chuffed to bits with em and they will be gracing my next build
The pics will tell the rest of the story
Cheers
It comes out of the ground!

Offline benno

  • Team Moderator
  • 900 Air
  • *
  • Posts: 3888
  • Rated:
Re: Home made Pro Class wheels
« Reply #1 on: November 10, 2018, 09:50 PM »
More
It comes out of the ground!

Offline benno

  • Team Moderator
  • 900 Air
  • *
  • Posts: 3888
  • Rated:
Re: Home made Pro Class wheels
« Reply #2 on: November 10, 2018, 09:52 PM »
More
It comes out of the ground!

Offline benno

  • Team Moderator
  • 900 Air
  • *
  • Posts: 3888
  • Rated:
Re: Home made Pro Class wheels
« Reply #3 on: November 10, 2018, 09:54 PM »
Finished
It comes out of the ground!

Offline chubby

  • BMX Nerd
  • *********
  • Posts: 4107
  • Needs Pegs
  • Rated:
Re: Home made Pro Class wheels
« Reply #4 on: November 10, 2018, 09:54 PM »
Not easier to buy some??

Sent from my G8341 using Tapatalk

WANTED : 1" freestyle forks, uglier the better

Offline benno

  • Team Moderator
  • 900 Air
  • *
  • Posts: 3888
  • Rated:
Re: Home made Pro Class wheels
« Reply #5 on: November 10, 2018, 10:06 PM »
Not easier to buy some??

Sent from my G8341 using Tapatalk
Yep but where’s the fun in that 👍🏼
It comes out of the ground!

Offline chubby

  • BMX Nerd
  • *********
  • Posts: 4107
  • Needs Pegs
  • Rated:
Re: Home made Pro Class wheels
« Reply #6 on: November 10, 2018, 10:08 PM »
It'll be somewhere

Sent from my G8341 using Tapatalk

WANTED : 1" freestyle forks, uglier the better

Offline Glynnyboy

  • Look Back
  • *****
  • Posts: 1569
  • Rated:
Re: Home made Pro Class wheels
« Reply #7 on: November 10, 2018, 10:15 PM »
Great work and an awesome read. Top job Mike  :4_17_5:

Offline Ady

  • Flip-Whip
  • ******
  • Posts: 1842
  • fin old..... they call me the silver fox
  • Rated:
Re: Home made Pro Class wheels
« Reply #8 on: November 10, 2018, 11:34 PM »
Myself did exactly the same on a pitted set of arayas and came up a treat.
It takes a lot of patience as you got to be spot on and the metal bits gets everywhere.
They use to do this originally as you get some sets with the araya stamping.
Top work mate  fistblump
Real men have Dachshunds I have three / now two 😓 missing you../ back too three with a rescue dachie

Offline burnerboy

  • Curb Endo
  • **
  • Posts: 81
  • Rated:
Re: Home made Pro Class wheels
« Reply #9 on: November 11, 2018, 12:02 AM »
Hey Mike, remember those old rubbish Arayas I gave you, can I have them back as I have a bike they can go on???

Top notch job as usual bud and great to see em saved.

Offline WINI

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3660
  • Sheeping it real ;-)
  • Rated:
Re: Home made Pro Class wheels
« Reply #10 on: November 11, 2018, 06:55 AM »
Great read and a top job Mike.

Look amazing
Neil, the bathroom's free. Unlike the country under the Thatcherite junta

Offline factory pilot

  • Team Owner
  • BMX Nerd
  • *
  • Posts: 4804
  • AKA Swiss Tony AKA Tony DeWonderful
  • Rated:
Re: Home made Pro Class wheels
« Reply #11 on: November 11, 2018, 07:35 AM »
Nice one Mike love this thread  :lighter:
"Knowledge is the acceptance of ones own ignorance." Socrates 399BC

Offline Retrodan72

  • Site Supporter
  • BMX Overlord
  • *
  • Posts: 16347
  • Rated:
Re: Home made Pro Class wheels
« Reply #12 on: November 11, 2018, 09:22 AM »
Best thread we’ve had in ages Mike.  :4_17_5:


GO FORWARD TO THE PAST, WITH NRP'S

Offline Bob_Acid

  • Team Admin
  • BMX Overlord
  • *
  • Posts: 17364
  • It's Bronked
  • Rated:
Re: Home made Pro Class wheels
« Reply #13 on: November 11, 2018, 09:49 AM »
Nice job Mike!

griff

  • Guest
Re: Home made Pro Class wheels
« Reply #14 on: November 11, 2018, 10:01 AM »
Great job Benno!
Always enjoy reading a good resto thread - nice to see a bit of TLC do wonders  :4_17_5:

Offline Taipan

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3620
  • Rated:
Re: Home made Pro Class wheels
« Reply #15 on: November 11, 2018, 10:02 AM »
Bloody excellent! they look the biz!  :daumenhoch:

can I ask out of curiosity? are the holes you drilled the same diameter as the hole that the original inner tube valve came thru?

Offline oldschoolace

  • Team Moderator
  • Double Flip Whip
  • *
  • Posts: 6818
  • Bodger
  • Rated:
Re: Home made Pro Class wheels
« Reply #16 on: November 11, 2018, 10:38 AM »
Nice Job  :daumenhoch:
kind of job lots of patience and measuring still doesnt make you immune from a mistake
You're right about the spoke spacings. something we all take for granted but they are far from equally spaced  ???
Sixteen thirty-two. What is that? A year?   No, it's your top score on Pole Position.


Offline BMX1973

  • Site Supporter
  • Berm Worm
  • *
  • Posts: 8415
  • Rated:
Re: Home made Pro Class wheels
« Reply #17 on: November 11, 2018, 11:35 AM »
They look fantastic and just as good as originals .

:4_17_5: class work  :daumenhoch:

Offline benno

  • Team Moderator
  • 900 Air
  • *
  • Posts: 3888
  • Rated:
Re: Home made Pro Class wheels
« Reply #18 on: November 11, 2018, 12:13 PM »
Bloody excellent! they look the biz!  :daumenhoch:

can I ask out of curiosity? are the holes you drilled the same diameter as the hole that the original inner tube valve came thru?
No mate the holes are bigger, I’ve done them at 11mm, I measured my og set and did them the same 👍🏼
It comes out of the ground!

In2bmx

  • Guest
Re: Home made Pro Class wheels
« Reply #19 on: November 11, 2018, 12:22 PM »
Amazing patience and work Mikey  :4_17_5:

Class  fistblump

Offline CustardLips

  • Site Supporter
  • Berm Worm
  • *
  • Posts: 7314
  • Rated:
Re: Home made Pro Class wheels
« Reply #20 on: November 11, 2018, 03:47 PM »
Nice work Mike... this thread makes me wanna make some and i don't even need em.  :LolLolLolLol:
"Every year is getting shorter, never seem to find the time"

"WWG1WGA"

Offline MartyC

  • Berm Worm
  • ***********
  • Posts: 8755
  • Radder than a Rad thing on a Rad day; maybe?
  • Rated:
Re: Home made Pro Class wheels
« Reply #21 on: November 12, 2018, 01:50 PM »
I remember one of the guys from Ruislip/Eastcote doing this bitd, not as neatly though...


Better to crash and burn than fade away

RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  Home made Pro Class wheels
 

gfxgfx
gfx gfx
Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
SimplePortal 2.3.5 © 2008-2012, SimplePortal